Welcome, Guest. Please login or register.
Did you miss your activation email?

Username: Password:

Author Topic: paint on water side of fire box  (Read 3669 times)

coaldozer

  • Training Wheels
  • *
  • Offline Offline
  • Posts: 11
  • OWF Brand: Home Made
  • OWF Model: Creek Heater
    • View Profile
paint on water side of fire box
« on: February 01, 2014, 04:41:43 PM »

 :-\ I read in a post that the water side of the water jacket should not be painted . Figure this goes for fire box too . my firebox is a 120 gal propane tank with some nice thick paint . I started removing some but after 1/2 hr  I had only cleaned up about half of the end. Does this really have to come off . I know the treatment needs to make contact with bare metal to work properly . I guess what I am really wanting to know is what kind of problems would develop from leaving the paint on ?
« Last Edit: February 02, 2014, 06:46:36 AM by coaldozer »
Logged

mlappin

  • Fabricator Extraordinaire
  • Global Moderator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4140
  • OWF Brand: homebuilt, now HeatmasterSS
  • OWF Model: Martin Steel Works Gen 1 then, now a G200.
  • North Liberty, Indiana
    • View Profile
    • Altheatsolutions
Re: paint on water side of fire box
« Reply #1 on: February 01, 2014, 04:47:18 PM »

Well biggest concern might be at some point in the future the paint starts to come off and plugs a water line, pump or heat exchanger.

Not sure what those tanks are painted with, might even be epoxy.

I'll let wiser heads chime in here, I bet somebody already has experience with this one way or another.
Logged
Stihl 023
Stihl 362
Stihl 460
Sachs Dolmar 112 and 120
Homemade skid steer mounted splitter, 30" throat, 5" cylinder
Wood-Eze model 8100 firewood processor

HeatmasterSS dealer for Northern Indiana

RSI

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3100
  • OWF Brand: HeatMaster
  • OWF Model: G200 and B250
    • View Profile
    • RSI
Re: paint on water side of fire box
« Reply #2 on: February 01, 2014, 08:09:39 PM »

I don't think it will hurt anything leaving paint inside the firebox. It will just burn off fairly quick so not worth putting it on if you start with bare steel.
Logged

mlappin

  • Fabricator Extraordinaire
  • Global Moderator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4140
  • OWF Brand: homebuilt, now HeatmasterSS
  • OWF Model: Martin Steel Works Gen 1 then, now a G200.
  • North Liberty, Indiana
    • View Profile
    • Altheatsolutions
Re: paint on water side of fire box
« Reply #3 on: February 03, 2014, 08:54:26 PM »

I don't think it will hurt anything leaving paint inside the firebox. It will just burn off fairly quick so not worth putting it on if you start with bare steel.

I think he's referring to the outside of the firebox since it started out as a propane tank.
Logged
Stihl 023
Stihl 362
Stihl 460
Sachs Dolmar 112 and 120
Homemade skid steer mounted splitter, 30" throat, 5" cylinder
Wood-Eze model 8100 firewood processor

HeatmasterSS dealer for Northern Indiana

RSI

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3100
  • OWF Brand: HeatMaster
  • OWF Model: G200 and B250
    • View Profile
    • RSI
Re: paint on water side of fire box
« Reply #4 on: February 03, 2014, 09:45:03 PM »

Ah, that make sense now. I just always think of the inside when firebox it mentioned.

I have no idea how much difference it will make but if I were doing it I would just clean off all the loose paint and put a Y strainer on the line just in case it does start coming off eventually.
Logged

mlappin

  • Fabricator Extraordinaire
  • Global Moderator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4140
  • OWF Brand: homebuilt, now HeatmasterSS
  • OWF Model: Martin Steel Works Gen 1 then, now a G200.
  • North Liberty, Indiana
    • View Profile
    • Altheatsolutions
Re: paint on water side of fire box
« Reply #5 on: February 03, 2014, 10:07:15 PM »

I'll agree with RSI, knock/scrape off any loose paint and run it with a strainer. Might loose a little heat transfer with the paint on, but I honestly can't see it being much.
Logged
Stihl 023
Stihl 362
Stihl 460
Sachs Dolmar 112 and 120
Homemade skid steer mounted splitter, 30" throat, 5" cylinder
Wood-Eze model 8100 firewood processor

HeatmasterSS dealer for Northern Indiana

Wood Nutt

  • Full Member
  • ***
  • Offline Offline
  • Posts: 144
  • OWF Brand: shaver
  • OWF Model: 250 Pro, Stihl 660, 290, 210, 031AV, Efco 3500
    • View Profile
Re: paint on water side of fire box
« Reply #6 on: February 04, 2014, 12:56:46 PM »

If you have a body shop near by, especially one that specializes in restoration work, many of them have media blasting rooms where they do car frames and similar.  They would be able to get the paint off pretty easily if you do want it off.
Logged
What this country needs is less dirty minds and more dirty fingernails!

slimjim

  • Full Member
  • ***
  • Offline Offline
  • Posts: 158
  • OWF Brand: Wood Doctor / HeatMaster
  • OWF Model: 14,000. / G 200 and G 400
  • Southern Maine
    • View Profile
    • www.mainlycustom.com
Re: paint on water side of fire box
« Reply #7 on: February 04, 2014, 01:42:18 PM »

  Simply set it on fire once you have the end cut off
Logged
Wood boiler sales, service and installation for the Northeastern USA.

coaldozer

  • Training Wheels
  • *
  • Offline Offline
  • Posts: 11
  • OWF Brand: Home Made
  • OWF Model: Creek Heater
    • View Profile
Re: paint on water side of fire box
« Reply #8 on: February 04, 2014, 02:41:54 PM »

Yea I thought about the fire but I have it in my garage now with the front plate welded on. So bought some paint remover today to give this a shot.
Logged