Welcome, Guest. Please login or register.
Did you miss your activation email?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
1
Plumbing / Re: baseboard heat system with a wood boiler..
« on: January 01, 2011, 08:56:10 AM »
I was thinking if there was a way i could tap directly in to the house boiler without the plate exchanger.. Only problem is that the wood boiler is a non pressurized unit.. like i said originally this is my 1st time ever dealing with any type of hydronic house boilers..
2
Plumbing / Re: baseboard heat system with a wood boiler..
« on: January 01, 2011, 08:48:08 AM »
willie the piping is 3/4" in the basebords, the heat exchanger has a 1" nipple then from there it is a 1 1/4" which feeds the existing home boiler. As for as how many feet in his house?? I was told that the existing home boiler could've reached an 80*temperature in the house on the gas...
3
Plumbing / Re: baseboard heat system with a wood boiler..
« on: December 31, 2010, 12:13:02 AM »
By the way it is a 1600 sq ft. ranch with a finnished basement, so right around 3000 sq ft...
4
Plumbing / baseboard heat system with a wood boiler..
« on: December 31, 2010, 12:09:25 AM »
Hello everyone, i am new to the site but not new to burning wood
I have installed a few wood boiler heating systems in my past but only one of them was in a baseboard heat system all the others were central air. This is at my father-in-laws home so I was safe using him as the guini pig for my first install in a baseboard heat system. First off He has a home made wood boiler and it runs at 170* the fan cycles once every 2-4 hours. I set the the system with 2 plate heat exchangers, a 20 for the hot water tank and a 50 plate with 1" nipples for the basebord boiler. The wood boiler is placed right next to the house where thier boiler room is so the 1" pex lines i used only travel 15' so there is pratically no heat wasted through the small distance.
The system has been up and running for a few months and produces a average of 73*-76* in the home even though the t-stat is set at 80*. Now My question is what is holding the system back from acheiving the set 80* on the t-stat? (Not complaining that 73*-76* is'nt hot just curious why it don't reach 80*) And yes both pumps are working fine on the boiler system and the wood boiler.
I have installed a few wood boiler heating systems in my past but only one of them was in a baseboard heat system all the others were central air. This is at my father-in-laws home so I was safe using him as the guini pig for my first install in a baseboard heat system. First off He has a home made wood boiler and it runs at 170* the fan cycles once every 2-4 hours. I set the the system with 2 plate heat exchangers, a 20 for the hot water tank and a 50 plate with 1" nipples for the basebord boiler. The wood boiler is placed right next to the house where thier boiler room is so the 1" pex lines i used only travel 15' so there is pratically no heat wasted through the small distance.
The system has been up and running for a few months and produces a average of 73*-76* in the home even though the t-stat is set at 80*. Now My question is what is holding the system back from acheiving the set 80* on the t-stat? (Not complaining that 73*-76* is'nt hot just curious why it don't reach 80*) And yes both pumps are working fine on the boiler system and the wood boiler.
Pages: [1]