Welcome, Guest. Please login or register.
Did you miss your activation email?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
1
General Outdoor Furnace Discussion / Re: Is there any 'real' difference?
« on: March 20, 2016, 07:15:15 PM »
What state are you in maybe someone can
Help you out
Help you out
2
Portage & Main / Re: New nossel for my 250
« on: February 28, 2016, 06:25:36 PM »
I ll pencil in a day with you and we will do a tear out the nozzle and bricks on the side and give it a good cleaning. By the way thanks on the fluid film job still looks great might be able to use it behind the bricks
3
Central Boiler / Re: Eclassic 1450 questions
« on: February 18, 2016, 10:16:32 PM »
What water temperature are you running your boiler at if on the low side
I would try bring the temp up
I would try bring the temp up
4
General Outdoor Furnace Discussion / Re: CB 5648
« on: February 07, 2016, 03:39:28 AM »
Only think of buying it if you can weld and I wouldn't pay any more then $2000 if that. Its hard to say how much life is left in it.
5
General Outdoor Furnace Discussion / Re: spray foam
« on: January 02, 2016, 05:39:58 PM »
Logstor 's the only way to go one continues run of pipe with no joints
Why waste time money and labor save it some place else
Why waste time money and labor save it some place else
6
General Discussion / Re: Sanding and Floor Finish
« on: January 02, 2016, 05:05:35 AM »
When you first sand the floors go at a 45 degree across the boards taking you rented a drum sander and edger this will keep the floor level as you get the old off also if you get a little wood scraper it works good in the corners for the stuff you can't get with the edger as far as finish PARKS
Polyurethane is very nice if they still make it 3 coats have fun
Polyurethane is very nice if they still make it 3 coats have fun
7
General Outdoor Furnace Discussion / Re: question about heating a office within a unheated building
« on: November 15, 2015, 02:34:16 AM »
How far as way is the office going to be from the owner or from your house
8
General Outdoor Furnace Discussion / Re: Torqued my knee
« on: November 02, 2015, 06:44:20 PM »
Maybe to old to spread the mustard but not old to lick the jar
9
General Outdoor Furnace Discussion / Re: 1" to 3/4" at DHW exchanger
« on: October 30, 2015, 12:45:49 AM »
The fittings you put in the end of the 1"pex will shrink the size down
So it will be for the better to use the 1"pex so go for it and have hot water
So it will be for the better to use the 1"pex so go for it and have hot water
10
Central Boiler / Re: 5036 Chimney
« on: October 20, 2015, 05:58:43 PM »
You should be able to get the pice you need from your
Dealer you will also need a rope gasket that goes on end in the boiler
Dealer you will also need a rope gasket that goes on end in the boiler
11
Central Boiler / Re: E1400 Crack Found
« on: September 10, 2015, 06:54:46 PM »
Good to hear that you got someone to weld it have some cold water handy he'll need a drink or 2 good luck
With the project
With the project
12
General Outdoor Furnace Discussion / Re: Fire safety
« on: June 26, 2015, 04:36:45 AM »
Points well made
13
Central Boiler / Re: E 1450 cement slab
« on: June 17, 2015, 03:38:22 AM »
I personally now put 2 inch blue insulation board under my boilers on top of the slab and make it the exact size of the boiler it gets the metal frame off the slab and out of snow and water the used boilers i have been getting the frames have been rusting out in places plus it on some boilers it adds to the insulation on the bottom of the boiler
14
General Outdoor Furnace Discussion / Re: Summertime blues.
« on: June 04, 2015, 06:01:26 PM »
Still burning 3 years straight no oil good way to clean up the yard waste
15
Central Boiler / Re: maxim 250 putting info together
« on: May 26, 2015, 06:22:26 PM »
A BIG THANK YOU for all the input it's all very helpful