Welcome, Guest. Please login or register.
Did you miss your activation email?

Username: Password:

Author Topic: Overheating issue/question  (Read 12722 times)

Leever2000

  • Training Wheels
  • *
  • Offline Offline
  • Posts: 19
  • OWF Brand: Mahoning
  • OWF Model: 200
    • View Profile
Overheating issue/question
« on: March 15, 2021, 10:05:14 AM »

My OW Furnace appeared to be overheating so I took a closer look. Noticed my T&P valve stuck open (defective?) and water a little more than trickling out. The water temperature is within the normal temperature limits and just wanted to get some feedback? I believe it  is just a T&P valve replacement? Can anything else cause the issue I am seeing or does it look like a T&P valve replacement? Thanks!

After some further investigation it appears the pressure valve is releasing at a lower temp (150 - 175 degrees F). I will replace the valve.



« Last Edit: March 15, 2021, 11:19:45 AM by Leever2000 »
Logged

mlappin

  • Fabricator Extraordinaire
  • Global Moderator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4140
  • OWF Brand: homebuilt, now HeatmasterSS
  • OWF Model: Martin Steel Works Gen 1 then, now a G200.
  • North Liberty, Indiana
    • View Profile
    • Altheatsolutions
Re: Overheating issue/question
« Reply #1 on: March 15, 2021, 01:39:31 PM »

My OW Furnace appeared to be overheating so I took a closer look. Noticed my T&P valve stuck open (defective?) and water a little more than trickling out. The water temperature is within the normal temperature limits and just wanted to get some feedback? I believe it  is just a T&P valve replacement? Can anything else cause the issue I am seeing or does it look like a T&P valve replacement? Thanks!

After some further investigation it appears the pressure valve is releasing at a lower temp (150 - 175 degrees F). I will replace the valve.

I didn’t realize Mahonings were pressurized. If replacing the valve solves it post back so others can see the fix if they have the same issue.
Logged
Stihl 023
Stihl 362
Stihl 460
Sachs Dolmar 112 and 120
Homemade skid steer mounted splitter, 30" throat, 5" cylinder
Wood-Eze model 8100 firewood processor

HeatmasterSS dealer for Northern Indiana

Leever2000

  • Training Wheels
  • *
  • Offline Offline
  • Posts: 19
  • OWF Brand: Mahoning
  • OWF Model: 200
    • View Profile
Re: Overheating issue/question
« Reply #2 on: March 15, 2021, 03:50:39 PM »

mlappin - thank you for the re-direct! You are correct the Mahoning furnace is not a pressurized furnace for the heat, but I do have a secondary loop for heating my potable (pre - water heater).

 I replaced the T&P valve and all is working well, the furnace has reached the operating temp and no water being dumped via the new T&P valve.

Earlier when mlappin was commenting I was out at the furnace trying to replace the T&P valve and was a little confused. I stopped and returned inside and read the mlappin comment and was no longer confused. I shut the potable water off to the furnace and replaced the defective T&P valve.

Thanks mlappin for bringing clarity!
« Last Edit: March 15, 2021, 04:55:13 PM by Leever2000 »
Logged

mlappin

  • Fabricator Extraordinaire
  • Global Moderator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4140
  • OWF Brand: homebuilt, now HeatmasterSS
  • OWF Model: Martin Steel Works Gen 1 then, now a G200.
  • North Liberty, Indiana
    • View Profile
    • Altheatsolutions
Re: Overheating issue/question
« Reply #3 on: March 15, 2021, 07:28:22 PM »

So if I understand correctly Mahonings have a secondary coil in the water jacket to heat your domestic hot water and at the furnace is a T&P valve just like a water heater?
Logged
Stihl 023
Stihl 362
Stihl 460
Sachs Dolmar 112 and 120
Homemade skid steer mounted splitter, 30" throat, 5" cylinder
Wood-Eze model 8100 firewood processor

HeatmasterSS dealer for Northern Indiana

Leever2000

  • Training Wheels
  • *
  • Offline Offline
  • Posts: 19
  • OWF Brand: Mahoning
  • OWF Model: 200
    • View Profile
Re: Overheating issue/question
« Reply #4 on: March 16, 2021, 11:06:28 AM »

Yes exactly correct!

I posted in the plumbing area originally because when I looked at the Mahoning posts, I was the last to post in 2018. I figured I would get visibility.

Thanks again, day 2 with new T&P valve all working smooth!
Logged