This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

1

Plumbing / Re: Hot water heater to heated water jacket

« on: December 18, 2016, 01:11:45 PM »

Attached a pic of the tank

2

Plumbing / Hot water heater to heated water jacket

« on: December 18, 2016, 01:10:13 PM »

Using a 25 gallon hot water tank to keep a water jacket warm on a tank.  The tank is doublewall and has 1" fittings on bottom and top opposite sides . Where would be the best place to put the pump

3

HeatMaster / Re: Heat master 10,000 e custom upgrades

« on: October 24, 2016, 01:21:38 PM »

Rear door on mine isn't hot but it doesn't seal well . Firebox door is always really hot. Thinking about putting ceramic board on inside of door

4

HeatMaster / Heat master 10,000 e custom upgrades

« on: October 23, 2016, 12:56:52 PM »

Just wandering if anyone has did any custom upgrades to their 10000e? Thinking about insulating the firebox door better. The outside of the door is always hot to touch. And the insulation on the water jacket is not that great either. Rear door doesn't seal well. I'm not bashing the stove just want to Improve it.

5

General Discussion / Re: Variable speed pumps pro and con

« on: October 08, 2016, 05:03:48 PM »

Only a few years old. Think seals went out last year underground pipe got hole and pump ran dry for awhile.

6

General Discussion / Re: Variable speed pumps pro and con

« on: September 25, 2016, 06:45:41 PM »

Seal went out on my Armstrong and costs 75 bucks . They sent me the wrong one so I'm thinking about upgrading .

7

General Discussion / Variable speed pumps pro and con

« on: September 25, 2016, 02:10:00 PM »

Looking at replacing my Armstrong e9 with a taco variable speed pump. Would this cut down on my wood consumption ? Any advice will be helpful. Thanks

8

General Discussion / Plumbing on heatmaster

« on: September 28, 2015, 08:03:51 AM »

Need to connect my 1" logstor pipe to 1" copper stub pipe one on top by the valve and other on bottom of pump. Had them hooked direct and stove shifted and moved during freezing and thawing. Need something more flexible. The lines would stretch out and leak at the compression fitting . Any ideas? Seen the flex stainless but heard it's junk .

9

HeatMaster / Re: trouble getting a bed of coals 10000e

« on: March 07, 2014, 03:46:56 PM »

I'm still burning coal and wood.I load amount of wood I need and throw in 3-4 shovel fulls of coal

10

HeatMaster / Re: trouble getting a bed of coals 10000e

« on: March 07, 2014, 08:04:38 AM »

Thanks guys I'll play around with it.I had a really good bed of coals then it bridged over from the coal so it might be from burning the stoker coal.I want to try the bigger stuff

11

HeatMaster / Re: trouble getting a bed of coals 10000e

« on: March 07, 2014, 07:35:35 AM »

Seems like I'm blowing through wood when I can't get a bed of coals

12

HeatMaster / trouble getting a bed of coals 10000e

« on: March 07, 2014, 06:54:56 AM »

ive been having trouble keeping a bed of coals!whats everyone running their fan draft setting at?mine is all the way open.just wandering if im getting too much air and blowing the coals to ashes?

13

HeatMaster / burning earcorn in your heatmaster

« on: February 25, 2014, 12:01:59 PM »

Has anyone burned ear corn in their headmaster?

14

HeatMaster / Re: Price increase!

« on: February 25, 2014, 10:00:43 AM »

Dang! Good thing I bought mine already.thanks to scott

15

Fire Wood / Re: what kind of wood is this?

« on: February 23, 2014, 05:59:05 PM »

Yep looks like locust .that stuff burns really hot.also hard on the chain!