Welcome, Guest. Please login or register.
Did you miss your activation email?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
1
Portage & Main / Re: Optimizer 250
« on: January 09, 2012, 06:16:28 PM »
I have mine inside a lean to on the side of my shop. it to fills with smoke i just open the doors and the wind takes care of the rest.
so far so good nice and warm in the house toasty in the shop. very impressed less work than running two wood stoves, and my shop is always warm, no condensation on my stuff. and i can`t belive there is hardly any smoke coming out the chimney, my nieghbours didn`t even know i put an OWB until i told them last week. and been running since october.
so far so good nice and warm in the house toasty in the shop. very impressed less work than running two wood stoves, and my shop is always warm, no condensation on my stuff. and i can`t belive there is hardly any smoke coming out the chimney, my nieghbours didn`t even know i put an OWB until i told them last week. and been running since october.
2
General Outdoor Furnace Discussion / Re: Rhino Flex Underground dual Pex
« on: June 19, 2011, 05:12:48 PM »
so i guess we will be moving to the portage and main board
3
General Outdoor Furnace Discussion / Re: Rhino Flex Underground dual Pex
« on: June 16, 2011, 07:08:54 AM »
Bill
Yes, i found some pipe.
Looks like i am heading for the border, for a shopping trip to the good old USA
i found a central boiler dealer near buffalo 11.00 a foot for thermopex
and a trip to Outdoor Furnace supply in Middleton Ny for the rest of the stuff ineed
probally going to pick up a new brushcutter too.
with exchange right now i`ll save roughly 1200 bucks
for a six hour drive.
Thanks
Pat
Yes, i found some pipe.
Looks like i am heading for the border, for a shopping trip to the good old USA
i found a central boiler dealer near buffalo 11.00 a foot for thermopex
and a trip to Outdoor Furnace supply in Middleton Ny for the rest of the stuff ineed
probally going to pick up a new brushcutter too.
with exchange right now i`ll save roughly 1200 bucks
for a six hour drive.
Thanks
Pat
4
Plumbing / Side Arm Sizing for DHW
« on: June 13, 2011, 02:32:39 PM »
Can you guys give me some ideas on sizing my side arm heater.
i will be making it myself as i have some stainless lying around the shop
i have a piece of 2.5 ID stainless i will be using for the outer jacket
should i go .75 with the water line or 1 inch. And what length should i make the whole unit
i plan on running a circulating pump on the hot water tank set-up.
Thanks
Pat
i will be making it myself as i have some stainless lying around the shop
i have a piece of 2.5 ID stainless i will be using for the outer jacket
should i go .75 with the water line or 1 inch. And what length should i make the whole unit
i plan on running a circulating pump on the hot water tank set-up.
Thanks
Pat
5
General Outdoor Furnace Discussion / Re: Rhino Flex Underground dual Pex
« on: June 10, 2011, 04:58:41 PM »
Brian was the best price but the problem is shipping
my friend ron drives truck to winnepeg weekly and he is going to pick up my unit
the problem is i need 12 feet of deck space on the truck for unit and pipe
if i just get the unit it is easier for ron because he can still fill the rest of the truck with wood
if i need 12 feet that is almost half of one of his trailers
and i would have to pay for what he would lose on wood. if its just the unit it is much easier
i can get urecon for 13.80 a foot and a 2 hour drive one way.
that price is from green valley in lucan ONT. they are the only ont dist for urecon
but they have been very helpful with different information so that`s where i am going to get it.
my friend ron drives truck to winnepeg weekly and he is going to pick up my unit
the problem is i need 12 feet of deck space on the truck for unit and pipe
if i just get the unit it is easier for ron because he can still fill the rest of the truck with wood
if i need 12 feet that is almost half of one of his trailers
and i would have to pay for what he would lose on wood. if its just the unit it is much easier
i can get urecon for 13.80 a foot and a 2 hour drive one way.
that price is from green valley in lucan ONT. they are the only ont dist for urecon
but they have been very helpful with different information so that`s where i am going to get it.
6
General Outdoor Furnace Discussion / Re: Rhino Flex Underground dual Pex
« on: June 08, 2011, 02:48:56 PM »
with shipping its not worth it, were did you get your urecon from
thanks
Pat
thanks
Pat
7
General Outdoor Furnace Discussion / Re: Rhino Flex Underground dual Pex
« on: June 08, 2011, 01:21:48 PM »
i don`t get my new house till june 30th
i will be paying for it this week and when i am ready my friend who hauls steel to winnipeg is going to pick it up for me
anytime i am ready. who did you get your urecon from best i can do is 13.80 a foot
and the rhino stuff is 10.50 only problem is urecon is a 2 hour drive and the rhino stuff is in il.
just waiting on a shipping quote, i need 190 feet so at almost a 3 dollar per foot savings it can be a big deal
i will be paying for it this week and when i am ready my friend who hauls steel to winnipeg is going to pick it up for me
anytime i am ready. who did you get your urecon from best i can do is 13.80 a foot
and the rhino stuff is 10.50 only problem is urecon is a 2 hour drive and the rhino stuff is in il.
just waiting on a shipping quote, i need 190 feet so at almost a 3 dollar per foot savings it can be a big deal
8
General Outdoor Furnace Discussion / Rhino Flex Underground dual Pex
« on: June 07, 2011, 06:29:57 PM »
Any one use this dual pex before its 10.50 a foot instead of 15.00 for urecon
9
Equipment / Re: Any welders here? Welding steel to cast iron?
« on: May 15, 2011, 07:02:46 PM »
309 stainless steel stick
preheat if you can and wrap it up when you are done
cast iron is tricky stuff, you have to reduce the amount of thermal shock to make it work
if you don`t preheat it could fracture the cast when you strke the arc
and if you don`t wrap it when done, it will crack beside the weld because it contracts to fast when cooling
best i can do to help you, you could try MIG but i wouldn`t recommend it
preheat if you can and wrap it up when you are done
cast iron is tricky stuff, you have to reduce the amount of thermal shock to make it work
if you don`t preheat it could fracture the cast when you strke the arc
and if you don`t wrap it when done, it will crack beside the weld because it contracts to fast when cooling
best i can do to help you, you could try MIG but i wouldn`t recommend it
10
General Outdoor Furnace Discussion / Re: Central E-Classic or Portage and Main gasifier
« on: May 11, 2011, 01:33:04 PM »
Portage and main gasifier 250
i think they seem to capture more heat before the smoke leaves the chimney
they were the cheapest for underground piping
just have to wait till i get so measurements on my new place before i order
delivery will be early july hopefully
Thanks
Pat
i think they seem to capture more heat before the smoke leaves the chimney
they were the cheapest for underground piping
just have to wait till i get so measurements on my new place before i order
delivery will be early july hopefully
Thanks
Pat
11
General Outdoor Furnace Discussion / Re: Central E-Classic or Portage and Main gasifier
« on: May 02, 2011, 06:25:02 AM »
There is no current regulation governing owb in my township
but there have been many complaints about smoke coming from units
The township told me that they are working on some sort of regulation
And they HIGHLY recommend that i go with a epa model to save future headache
but there have been many complaints about smoke coming from units
The township told me that they are working on some sort of regulation
And they HIGHLY recommend that i go with a epa model to save future headache
12
General Outdoor Furnace Discussion / Central E-Classic or Portage and Main gasifier
« on: May 01, 2011, 12:44:14 PM »
Hello
i am new to the forum, and looking to install a OWB at my new house
Can`t decide between the two, e classic or PandM gasifier
i won`t install a no epa unit andthis seem to be the two most helpful dealers i have called
i have a 2200 country bungalow 23 years old and a 34 X 56 insulated shop plus the hot water in te house
does any one have a experience with these wo units
Thanks
Pat
i am new to the forum, and looking to install a OWB at my new house
Can`t decide between the two, e classic or PandM gasifier
i won`t install a no epa unit andthis seem to be the two most helpful dealers i have called
i have a 2200 country bungalow 23 years old and a 34 X 56 insulated shop plus the hot water in te house
does any one have a experience with these wo units
Thanks
Pat
Pages: [1]