Welcome, Guest. Please login or register.
Did you miss your activation email?

Username: Password:

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - pointer80

Pages: [1] 2 3
Hey all,  I have a question,  I drain and flush/refill my outdoor boiler and add boiler treatment every heating season before initial start up.  My question is how many of you purge the air out of your water lines?  Also if you do how do you go about it?  Thanks.

Fire Wood / question on cutting on shares
« on: September 10, 2018, 08:59:21 AM »
Hello all,  My neighbor had roughly 100 trees taken out by loggers and give me all the tops.  It's mostly red oak.  I was going to try to find someone to cut on shares.  I was curious how cutting on shares works?  Load for load, two to one etc?  Thanks all.

General Outdoor Furnace Discussion / Re: input wanted on workshop heater
« on: January 11, 2017, 04:25:41 PM »
I do not know the brand as it was made by a little manufacturing facility.  I believe it is a 100,000 btu unit

General Outdoor Furnace Discussion / Re: input wanted on workshop heater
« on: January 10, 2017, 11:08:01 AM »
Thanks guys for all the input

General Outdoor Furnace Discussion / input wanted on workshop heater
« on: January 09, 2017, 12:22:28 PM »
hello all,  I wanted some input on my workshop heater.  Right now I have a hanging heater in my 30'x30'x10' workshop and although it does a good job keeping it warm here in the northern Michigan winter I was wondering if I dropped it down closer to the floor how much more warmth would I get out of it.  The nice thing about it's current location is it's up out of the way.  Also is better units out there for heating my work space.  One thing I have to look at is I already have this unit.  Thanks everyone.

General Outdoor Furnace Discussion / Re: insulated lines in my shop
« on: October 12, 2015, 02:47:34 PM »
The pipes run about 45 feet inside my shop.  The cavity is pretty tight but I never have had problems with the lines expanding much when the lines were in my shop before. 

General Outdoor Furnace Discussion / insulated lines in my shop
« on: October 11, 2015, 08:40:55 PM »
I just ran new lines into my shop and built insulated cavity to house them.  Here are some pictures

thanks guys

Plumbing / Re: question on hanging heat exchanger in barn
« on: October 08, 2015, 09:53:49 AM »
Hey thank you guy's,  That makes perfect sense. 

Plumbing / question on hanging heat exchanger in barn
« on: October 07, 2015, 04:54:14 PM »
hello all,  I have a 100,000 btu hanging heat exchanger in my workshop and I have a question about the feed and return lines.  Does it matter how I hook up the lines to the hanging unit?  What I mean is which line goes on the top or bottom hook ups on the hanging unit?  Thanks all.

what kind of supply house would have it? 

I cannot bring above ground.  The roof membrane would work but you have to buy a large quantity.

it is pvc pipe in another pipe with foam insulation between the two pipes.  I do not know the brand.  It was put in when my stove was installed about 9-10 yrs. ago.


Hello all,  I am wanting opinions on how to join two sections of this pipe together.  My water lines run through this pipe into my workshop and I had to take it apart to run new lines.  I need to attach two sections of this pipe and the joint will be slightly underground.  They made a rubber membrane adhesive wrap at one time to wrap the joint but I do not know if they are still available.  Any opinions on best way to attach these together. 

Pages: [1] 2 3