Welcome, Guest. Please login or register.
Did you miss your activation email?

Username: Password:

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - tinfoilhat2020

Pages: [1] 2 3 ... 43
I see one common denominator

Crown Royal / Re: Prestine series
« on: March 04, 2019, 07:33:11 PM »
They are great Boilers, very robust and well made. Not finicky at all.

Slim you need mental help my man

 :bag: :bag: :bag: :bag: :bag: :bag: :bag: :bag: :bag: :bag: :bag: :bag: :bag: :bag: :bag:

General Outdoor Furnace Discussion / Re: Dragon splatter
« on: February 04, 2019, 07:04:24 PM »
looks like your loving those oak slabs :) I love them too!!!!

Crown Royal / Re: Boiler Room Set-Up
« on: January 25, 2019, 01:22:53 PM »
wood consumption is very comparable. both are a solid unit and burn clean and efficient.

General Outdoor Furnace Discussion / man this forum has dropped off.....
« on: January 03, 2019, 08:52:44 PM »
wow, this forum has really dropped off. do you think it is mostly because of other wood burning groups on FB?

HeatMaster / Re: 2018 HeatMaster install pics
« on: December 26, 2018, 02:34:44 AM »
Just did this G400 the other day. House and shop, 3 air handlers in the shop, one in the house.
Just fired the first time when this pic was taken. Cleared up in less than an hour and gassed beautifully.

Do you ever have issues with that wrapped pipe? man that crap scares me.....

Install looks good!

Crown Royal / Re: The New Crown Royal Pristine web page
« on: December 26, 2018, 02:30:41 AM »
99% sure every manufacturer is kind of waiting around to see what the EPA is going to do.

And yes you are correct, the EPA numbers are based off of their old design. They did not change any air ways, so they still comply, but no further testing has been done

HeatMaster / Re: Stack temps
« on: December 07, 2018, 03:23:57 AM »
Last year I monitored them all year. Temps were generally in the 350-450 range, sometimes a bit higher.

HeatMaster / Re: G200 water flow
« on: November 13, 2018, 02:44:33 PM »
stack temps on my G200 with over 20GPM flow (3 pumps hooked up), my flue gas temps averaged 350-475 on hot burn cycles with seasoned oak.

HeatMaster / Re: Adding a second exchanger...
« on: November 13, 2018, 02:42:08 PM »
what size pump do you currently have?

Fire Wood / Re: Burning"Pressure Treated" lumber scraps?
« on: September 28, 2018, 07:19:59 PM »
all my cut offs go in the boiler...plenty of treated chunks over the years...even the gassers liked the treated stuff, burn hott >:D >:D >:D

Plumbing / Re: Copper VS PEX
« on: September 14, 2018, 03:43:13 PM »
can beat the look of copper....I ran 1 1/4 pex underground and all 1" copper inside home and buildings as I didn't want to lose flow, plus I love the look and feel of copper over pex

Crown Royal / Re: 7400E Boiler Room Project Completed
« on: September 07, 2018, 05:41:38 PM »
Good lighting is important! Fine looking job you did there, bet that slab cost as much as the building did.

Slab actually wasn't to bad, costs me about $600 installed for a 12 x 20


Pages: [1] 2 3 ... 43